logo
홈 뉴스

PVC Cable Temperature Rating: The 70°C Limit, Derating and XLPE Alternatives

중국 Shanghai Shenghua Cable (Group) Co., Ltd. 인증
중국 Shanghai Shenghua Cable (Group) Co., Ltd. 인증
좋은 공급자, 빠른 속도 응답, 빠른 배달 시간, 고품질 제품. 나는 운이 좋습니다 당신을 찾아내기 위하여!

—— John Smith

우리는 5 년간 그(것)들을 사용할 것이다 함께를 사용에, 그들입니다 좋은 공급자 및 좋은 친구의 우리의 명예 이었습니다.

—— Mohamed Rebai

나는 이 회사의 서비스에 아주 만족합니다, 그들의 사업이 더 낫고 더 나을 것이라고 나는 믿습니다.

—— 다니엘

당신이 저희를 주었다 당신의 직업적인 발표 및 서비스는 기립 박수를 할 만했습니다. Shenghua는 더 밝은 미래를 보내야 합니다.

—— Rendell Brewster

우리는 당신이 그것을 할 수 있도록 도와 줄 것입니다.

—— KHADBAATAR

제가 지금 온라인 채팅 해요
회사 뉴스
PVC Cable Temperature Rating: The 70°C Limit, Derating and XLPE Alternatives

Summary

The PVC cable temperature rating of 70 degrees Celsius is the number that quietly decides how much current a PVC insulated cable can carry and how long it will last in a hot plant room. Buyers routinely compare PVC and XLPE cables on price per metre while ignoring that the same cross section carries roughly 15 to 20 percent more current with XLPE insulation, and that every 8 to 10 degrees of sustained over-temperature halves insulation life. This guide explains what the 70 degree limit represents, how PVC behaves above it, how to derate for real ambient conditions, and when a 105 degree heat resistant PVC or an XLPE alternative is the cheaper engineering answer. It ends with six practical answers on hot locations, terminal ratings and short circuit allowances.

90 degree rated XLPE insulated power cable with PVC jacket, 2 to 5 cores

What the 70 Degree Rating Actually Means

A cable temperature rating is the maximum continuous conductor temperature at which the insulation is expected to achieve its design life, normally 20 to 30 years. For PVC insulation that figure is 70 degrees Celsius, set by the point at which the compound begins to soften, the plasticiser starts to migrate and the mechanical properties fall away. The rating refers to the conductor, not the sheath and not the air around the cable. In a 40 degree plant room a PVC cable rated 70 degrees has only 30 degrees of thermal headroom for the current it carries, which is why the permitted current falls quickly as ambient rises.

Two related limits are often confused with it. The first is the short circuit allowance, about 160 degrees Celsius for a few seconds, which is used to size the conductor for fault withstand rather than for continuous load. The second is the maximum conductor temperature of special compounds: heat resistant PVC is available at 90 and 105 degrees Celsius, and silicone reaches 180 degrees or more. Using a 105 degree PVC cable where a standard PVC cable would fail is a legitimate solution, but only if the termination and the connected equipment are also rated for that temperature.

InsulationContinuous conductor tempShort circuit tempRelative current
Standard PVC70 C160 CBaseline
Heat resistant PVC90-105 C160 CSlightly higher, size dependent
XLPE90 C250 CAbout 15-20 percent higher
XLPO / EPR90-120 C250 CSimilar to XLPE
Silicone180-200 C350 CLower per mm2, selected for heat

The practical consequence is that a PVC cable and an XLPE cable of the same size are not interchangeable when the load is near the rating. The PVC option will run hotter for the same current, age faster and eventually fail at a termination or in the middle of a run, and the failure will usually be attributed to a bad batch rather than to a design error.

Why the Limit Is So Often Exceeded in Practice

Designers rarely choose to overload a cable. Overheating usually comes from assumptions that were reasonable on the drawing and wrong on site.

1. Ambient taken from the wrong place. A design that uses 30 degrees Celsius for a cable running through a roof void, a ceiling plenum or a boiler room is already wrong at commissioning. Those spaces routinely run 15 to 25 degrees above the general building ambient, and the cable has no way to shed the heat.

2. Grouping ignored. Cables bunched in a tray or pulled into a single duct heat each other. A circuit sized in free air loses 15 to 30 percent of its capacity once four or five loaded cables share a tray, and the correction factor is frequently left out of the schedule.

3. Installation method changed on site. A cable designed for a ventilated tray may be installed in a conduit or buried in insulation by the time the building is finished. Each change lengthens the thermal path, and none of them generates a revised calculation.

4. Terminals rated higher than the cable. Equipment is commonly supplied with terminals rated 90 or 105 degrees Celsius. Connecting a 70 degree PVC cable to those terminals is thermally mismatched even when the current is well within the cable rating, and some inspectors will reject it on that basis alone.

5. Load growth. A feeder installed for a 60 percent load factor is often loaded to 90 percent five years later after an extension. The PVC insulation that was adequate at design has no margin left, and the ageing process accelerates sharply from that point.

How to Apply the Rating and Choose the Alternative

Start by measuring the ambient where the cable will actually run. Walk the route with a thermometer in summer if possible; a five minute check is more reliable than an assumption. Add the effect of any local heat source, then apply the correction factors for ambient, grouping and installation method, in that order. For a PVC cable carrying 100 A in free air at 30 degrees Celsius, a 45 degree ambient alone typically reduces the permissible current to about 85 A, and grouping four loaded cables in a tray can take it below 75 A. Sizing on the catalogue figure of 100 A would overload the cable by a quarter.

Then examine the alternatives in order of cost effectiveness. Reducing the load or splitting the circuit is free. Increasing the cross section keeps the same insulation family and is predictable, but copper is the dominant cost, so a one step increase may cost more than changing insulation. Changing from PVC to XLPE costs a little more per metre but raises the conductor limit to 90 degrees and increases the current for the same size by roughly 15 to 20 percent, which frequently removes the need for a larger conductor. Selecting a 105 degree heat resistant PVC is appropriate for short high temperature sections and for equipment connections, but it does not improve the current rating as much as XLPE and it costs more than standard PVC.

Check the interfaces as carefully as the cable. Terminal blocks, glands, enclosures and junction boxes are all rated for a temperature, and the lowest rating in the chain governs. A 90 degree cable entering a 70 degree junction box is a design fault waiting for an inspector. Where a cable must pass through a genuinely hot zone, a short silicone or glass braided section with proper transition joints is usually cheaper and safer than specifying an expensive high temperature cable for the whole route.

Finally, verify after energising. A thermal camera survey at commissioning, repeated under full load, will show any termination running hotter than its neighbours. That comparison is the most sensitive indicator available, because a loose joint or a wrongly sized cable shows up as a temperature difference long before it fails. Record the readings and repeat annually; a rising trend is the earliest warning of an ageing insulation or a degrading connection.

LocationTypical ambientAppropriate insulation
Air conditioned room25-30 CStandard PVC acceptable
General industrial hall35-45 CXLPE preferred, PVC derated
Roof void or plenum45-55 CXLPE, derated for ambient
Boiler house or furnace area60-100 CSilicone or special high temperature
Equipment with 90 C terminalsAnyXLPE or 90 C rated minimum
Buried duct20-25 C soilPVC or XLPE with soil factor

Product examples include the CU/XLPE/PVC 0.6/1 kV 3x120 plus 2x70mm2 cable for general distribution, the 90 degree rated 2-5 core XLPE cable with PVC jacket, and the PVC sheathed 3Cx300 XLPE cable for heavy feeders. Where PVC insulation is retained, the UL standard 500 metre PVC insulated multi-core cable and the steel wire armoured PVC cable cover buried and industrial duty, while the double PVC jacket 7x26 600 V cable adds mechanical protection. Genuinely hot locations are better served by a high temperature cable with LSZH insulation and black jacket.

Case Study: A Hotel Refurbishment in a Hot Climate

A 120 room hotel refurbishment in a coastal tropical city reused the original riser shafts, where summer temperatures reach 48 degrees Celsius. The consultant's schedule specified PVC insulated 4x25 mm2 feeders sized on a 30 degree ambient, which at 48 degrees gives roughly 78 A against a design load of 95 A. Commissioning revealed warm cables and a voltage drop at the far end above the permitted limit. The remedy was not a larger PVC cable but a change to XLPE insulation of the same cross section, which restored the margin and cut the voltage drop slightly through a lower operating temperature. The cost difference was under 8 percent of the cable value, against a re-pull cost that would have included opening finished ceilings on five floors.

The lesson generalises: in hot climates and in refurbishments where the route cannot be changed, insulation material is usually the cheapest lever available. Before ordering a larger PVC cable, calculate the same circuit in XLPE at the real ambient and compare the total installed cost. In most cases the XLPE option wins, and it also protects against the load growth that follows any successful hotel or commercial project.

There is also a commercial argument that is often overlooked. A PVC cable sized at 70 degrees for a hot location forces a larger conductor, and copper is by far the largest element of cable cost. Upgrading insulation from PVC to XLPE typically costs a few percent per metre, while a one step increase in conductor size can cost 25 to 35 percent more. On that arithmetic, the insulation upgrade pays for itself before the first metre of cable is delivered, and it leaves the circuit with thermal headroom that can absorb a future extension without civil work. Buyers who compare only the price per metre of two seemingly similar cables miss this entirely, because the comparison that matters is total cost at the same duty, at the same ambient, with the same derating factors applied.

Record the outcome. A cable schedule that shows the ambient used, the factors applied and the resulting rating is the only defence available if the circuit later overheats, and it is trivial to produce at design stage. Without it, a failure is explained by opinion rather than by data, and the discussion drifts towards the cable quality instead of the thermal design. Two lines per circuit in the project file settle that argument permanently.

FAQ

What happens if a PVC cable runs above 70 degrees Celsius?

Plasticiser migrates, the compound embrittles and mechanical and dielectric properties fall. As a rule, each 8-10 degrees of sustained over-temperature halves the expected service life.

Is the 70 degree limit the ambient temperature?

No. It is the maximum conductor temperature. The permitted ambient depends on the current and on the installation and grouping factors applied to that rating.

Can heat resistant PVC replace XLPE?

Sometimes, for short high temperature runs, but it does not raise the current rating as much as XLPE and costs more than standard PVC. XLPE is usually the better general solution.

Why does XLPE carry more current at the same size?

Because the 90 degree conductor rating leaves more temperature headroom above ambient, so the permissible current is roughly 15-20 percent higher for the same cross section.

Do terminals need to match the cable rating?

Yes. The lowest rated component in the chain governs, so a 70 degree cable on a 90 degree terminal block is a mismatch that inspectors may reject.

What is the short circuit temperature of PVC?

About 160 degrees Celsius for a few seconds. It is used to size the conductor for fault withstand, not for continuous loading.

Conclusion

The 70 degree PVC limit is not a formality; it sets current capacity, insulation life and often the cable size. Measure the real ambient, apply the derating factors in the correct order, check every terminal in the chain, and compare the cost of upsizing the conductor against the cost of moving to XLPE. That comparison usually favours XLPE in hot locations and in any installation where load growth is likely. Shanghai Shenghua Cable Group manufactures standard PVC, heat resistant PVC and XLPE cable from 0.6/1 kV distribution to 33 kV screened designs, with current rating tables and derating guidance supplied with each quotation. Send your route conditions, ambient data and load profile through our contact page and our engineers will return a sized cable schedule with the calculation attached.

선술집 시간 : 2026-11-17 15:43:16 >> 뉴스 명부
연락처 세부 사항
Shanghai Shenghua Cable (Group) Co., Ltd.

담당자: Ms. Mayling Zhao

전화 번호: 86-21-68172999

팩스: 86-21-58179888

회사에 직접 문의 보내기 (0 / 3000)